What Does Soffit and Fascia Replacement Cost in Jacksonville, FL?

Quick Answer (TLDR)

Soffit and fascia replacement runs roughly $9 to $34 per linear foot installed, which puts a typical project between $900 and $6,800. Most homes have 100 to 200 linear feet of roofline, so at 150 feet you are usually looking at $1,350 to $5,100 depending on material and condition. Fascia alone runs $6 to $10 per foot in wood, $7 to $14 in vinyl, and $10 to $22 in aluminum. Soffit alone runs $5 to $17 in wood, $7 to $20 in vinyl, and $9 to $30 in aluminum. A second story adds 10 to 15 percent, and hidden rot is the variable that moves the number most, because rotted board has to come off rather than get covered up. If you want the full service picture first, start with our soffit and fascia work in Jacksonville.

Why Roofline Repair Costs More in Jacksonville Than the Brochure Says

Jacksonville gets 53.4 inches of rain a year, according to the NOAA 1991 to 2020 normals for the airport station. The national average sits around 30 inches. That is not a small gap, and it is not spread evenly across the calendar.

June brings 7.60 inches, September 7.56, August 6.88, and July 6.77. Four months carry roughly half the year’s rainfall, and those four months sit inside hurricane season. Meanwhile November averages 2.00 inches. Your roofline gets hammered for a third of the year and then dries out.

That wet-dry-wet cycle is what breaks wood fascia. Paint film lifts, water gets behind it, the board stays damp through August, and the fastener holding your gutter loses its grip. By the time a homeowner calls us, the question is rarely whether the fascia needs work. It is how much of it.

Soffit and Fascia Replacement Cost by the Linear Foot

This work is priced by the linear foot of roofline, not by square footage. That is the number to ask for when you compare quotes, because a total dollar figure means nothing until you know how many feet it covers.

Combined soffit and fascia, installed

$6 to $22 per linear foot on the lower published range
$9 to $34 per linear foot on the wider range, which is where most real projects land
$900 to $6,800 for a typical whole-home project

Fascia only, by material

Wood fascia: $6 to $10 per linear foot
Vinyl or PVC fascia: $7 to $14 per linear foot
Aluminum fascia: $10 to $22 per linear foot
Average across materials: about $14.60 per linear foot

Soffit only, by material

Wood soffit: $5 to $17 per linear foot
Vinyl soffit: $7 to $20 per linear foot
Aluminum soffit: $9 to $30 per linear foot
Composite soffit: $5 to $25 per linear foot

One honest note on these figures. They come from national cost data, not from a Jacksonville-specific published survey, because no such survey exists that we can point you to. We are giving you the national ranges as national ranges. Your actual quote depends on your roofline, and any contractor who quotes you a per-foot price sight unseen is guessing.

What Actually Moves Your Number

How much roofline you have

Most homes run 100 to 200 linear feet. A simple rectangular ranch is at the low end. A home with dormers, bays, multiple gables, and a wrapped porch can exceed 200 feet on a footprint that looks modest from the street.

One story or two

A second story adds 10 to 15 percent. It is a staging and safety cost, not a material cost. Steep pitch or tight access on top of that pushes it higher, and in genuinely difficult cases the per-foot price can reach $40.

How much rot is behind the trim

This is the variable nobody can price from the driveway, and it is the one that decides whether your project lands at the bottom or the top of the range. Sound board can often take an aluminum wrap. Rotted board cannot, and covering it is the single most common way homeowners in this market get shortchanged. More on that below, because it matters more than the price list.

Labor, tear-off, and disposal

Labor runs $2 to $7 per linear foot of the total. Tear-off and disposal add $1 to $2 per foot, usually bundled into the labor line rather than itemized. If a quote separates these, that is a good sign, not a red flag.

Paint and finish

Wood needs paint. Aluminum and vinyl come finished, though aluminum can be repainted later if the finish chalks. Painting to match existing trim is an extra line on a wood job and is worth confirming is included before you sign.

The Aluminum Wrap Question, Answered Straight

Here is the thing most quotes will not explain. Aluminum fascia is frequently not a replacement at all. It is coil stock bent and capped over the wood fascia you already have. The trade calls it fascia wrap or fascia capping.

Done right, over sound wood, it is a legitimate and durable option. Done wrong, it is the most expensive mistake on this list, because wrapping does not replace rotted board and it does not let wood breathe. Water that gets behind the metal stays there.

Three specific ways it goes wrong:

Wrap over rot. The rot keeps going underneath, out of sight, and you have paid for new fascia while the structural problem continues.
Wrap cut short at the top. Water runs over the upper edge and sits trapped between metal and wood, which produces heavy rot over time in a spot you cannot inspect.
Wrap installed under existing gutters. This traps water between the fascia and the gutter and drives both corrosion and rot.

The correct sequence is inspect, replace what is rotten, then bend aluminum to fit tight. If a contractor quotes you fascia wrap without getting on a ladder and pressing on the board first, you do not have an inspection, you have a sales call.

Why Your Gutters Are Usually the Reason the Fascia Failed

Gutters hang on the fascia board. Every hanger and every fastener transfers the weight of the gutter, plus whatever water and debris are sitting in it, directly into that wood.

When a gutter clogs and overflows, water sheets down the face of the fascia instead of running through the system. The board stays wet through a Jacksonville summer. The wood softens, the fastener loses its bite, and the gutter starts to sag, which makes it hold more standing water, which soaks the board further.

That is why a sagging gutter is so often a fascia problem wearing a gutter costume. Rehanging a gutter on soft wood buys you a season at most. We check the board before we rehang anything, because putting good hardware into bad wood is not a repair.

The 2006 Line That Decides How Your Soffit Handles a Storm

Soffit wind resistance was not written into Florida code until 2006. Before that, in the most hurricane-prone state in the country, there was no soffit wind standard to build to.

The consequence shows up in the damage data. A survey of 195 single-family homes hit by the 2004 Florida hurricanes found soffit damage on about 25 percent of homes built between 2002 and 2004, against 45 percent of homes built between 1994 and 1998. The researchers found no meaningful difference in installation quality. The older homes simply had wider roof overhangs, and wider overhangs fail at lower pressures.

Testing done at the University of Florida for the Florida Building Commission found that failures occurred at wind speeds around 110 mph, well inside what a Jacksonville hurricane delivers. It also found that the dominant failure mode is panels unlocking from their channels, not fasteners tearing out.

The part that matters most for your house: losing soffit panels is not really a structural problem. It is a water problem. Once the panel is gone, wind-driven rain goes straight into your attic, soaks the insulation, and the Florida Division of Emergency Management notes that saturated insulation can bring a ceiling down. The same testing found water entering through intact soffits too, at increasing rates as pressure rose.

If your home predates 2006, your soffit was never designed to a wind standard. That does not mean it needs replacing tomorrow. It means the pre-season inspection is worth doing.

Termites, and Why Riverside Comes Up So Often

Formosan subterranean termites turned up in Duval County in 2015 at the former Women’s Center building at the Cummer Museum. The infestation was severe enough that a 90-year-old building on the National Register of Historic Places had to be demolished. Pest control companies then found them at nine more locations around Riverside.

Formosan colonies can exceed two million members, and in the worst cases they leave a paper-thin surface over wood that has been hollowed out. Native subterranean and drywood termites are endemic here as well.

Wood trim at the roofline is an entry point, particularly when it is already damp. Riverside is both the neighborhood with the documented Formosan cluster and a neighborhood full of century-old homes with wood detailing everywhere. If you are in Riverside, Avondale, Springfield, or San Marco and your fascia is soft, get a real look at it rather than a coat of paint.

What Replacement Looks Like on the Job

Most soffit and fascia jobs finish in one to two days depending on how much roofline is involved and how much rot turns up once the old material is off.

The sequence is straightforward. We take the gutters down, remove the damaged soffit and fascia, and look at what is behind it, including the rafter tails. Rotted material comes out. New fascia goes on, then soffit with the right ventilation, then the gutters go back up on sound wood with proper hangers.

Attic ventilation is the step that gets skipped. Soffit vents are how air enters your attic, and blocking them to make a panel fit trades a roofline problem for a moisture and cooling problem inside the house.

Permits in Duval County

The City of Jacksonville Building Inspection Division enforces the Florida Building Code and issues permits for Duval County. Roof replacements and significant repairs require permits, and soffit and fascia work generally requires one, particularly when it is part of a re-roof or a storm repair.

We say generally because we could not find a Duval line item stating that standalone soffit and fascia replacement always requires a permit. Confirm with the Building Inspection Division for your specific job. Any contractor who tells you a permit is never needed for roofline work on a storm repair is telling you something they cannot back up.

Frequently Asked Questions

How much does soffit and fascia replacement cost for an average Jacksonville home?

At 150 linear feet of roofline, which is typical, expect roughly $1,350 to $5,100 depending on material and how much rot is found. Vinyl at the low end and aluminum on a two-story home with significant rot at the high end. The published national range for a whole-home project is $900 to $6,800, and where you land inside it is mostly a question of material choice and hidden condition.

Can I replace just the rotted section instead of the whole roofline?

Often yes, and we will tell you when that is the honest answer. Isolated damage from one bad downspout or one clogged corner can be handled as a section repair. The catch is that rot rarely stops at a tidy boundary, so we open it up and look before committing to a number. If more than half your roofline is soft, replacing the whole run usually costs less than repairing it twice.

Is aluminum worth the extra cost over vinyl in Jacksonville?

In full sun on a south or west exposure, usually yes. Vinyl softens and warps starting around 160 to 165 degrees, and dark colors reach that surface temperature on a Jacksonville August afternoon. Vinyl typically lasts 15 to 20 years here, but only 10 to 12 on full-sun exposures. Aluminum costs more up front and dents more easily, but it holds up to the heat and UV better.

Does my homeowners insurance cover soffit and fascia damage?

Storm damage is often covered, and gradual rot from years of overflowing gutters generally is not, because insurers treat that as a maintenance issue. That distinction is exactly why the timing of your claim matters after a named storm. We can document what we find, but we do not file claims or advise on coverage. Your adjuster makes that call.

How long does soffit and fascia replacement take?

One to two days for most homes. Longer if there is extensive rot in the rafter tails behind the fascia, because that is structural work that has to be done properly before new trim goes on. We tell you if we find that once the old material is off, along with what it changes about the price, before we keep going.

Will replacing the fascia fix my sagging gutters?

If the fascia is why they sag, yes. That is the most common cause we see, because gutters hang on the fascia and soft wood cannot hold a fastener. But if the gutters are undersized for your roof or pitched wrong, new fascia will not fix the overflowing, and you will be back in the same spot next summer. We check both before quoting either.

Get a Straight Answer on Your Roofline in Jacksonville

If your paint is peeling along the roofline, your gutters are pulling away, or you heard something moving in the attic after the last storm, the useful next step is having someone put a ladder on it and press on the board. That is a free inspection, not a sales call.

Clean Cut Gutters is a local Northeast Florida crew, licensed and insured, with 78 five-star Google reviews. We handle soffit and fascia repair and replacement across Jacksonville and Duval County, and we will tell you when a section repair does the job instead of a full replacement. Call or text 904-888-9778 for a free inspection.